Cars Guide

As you know, since September last year in Russia enacted a new technical regulation on safety of wheeled vehicles, whereby the windshield, front side windows and the front glass door of the car must have a light transmittance of at least 70 percent . In practice, this effectively means a ban on the use of tinted glasses on data from the vehicle. We will not speculate on whether this ban and the reasons for its introduction, the adherents of a ride in the "tanks" or "tanks" have long been debating about it for a different car forums. Moreover, in addition to the requirements the traffic police to remove the tinting may be still a number of objective reasons. The film eventually wears away and scratched, lose its original luster, fade under the action of sunlight, which does not add points appearance cars. The purpose of this article - to tell how quickly and accurately independently rastonirovat glass without excessive costs, given that rastonirovka at SRT costs an average of one third the price of toning. So, for the successful implementation of the conceived need a hair dryer building (capacity not less than 2 kW), a razor, or better yet a scraper (see photo) or, in extreme cases, metal engineering ruler, spray washing windows (can be any good, but it is desirable to alcohol content); newsprint. By itself, the process of removing the film is not a daunting job, but will require patience and care. Better to start from the top. A small portion of the glass surface to heat the dryer, while still controlling the uniformity of heating. When under the influence of hot-air film is about to start to melt, with srebka or razor to pry its edge. If an instrument of labor is a line, you need to press it to the surface and move, and the film should get together like an accordion. Now the matter of technology - embarked on the edge of the film hands and pull down to accelerate the process, you can warm up the bottom of the glass. After separation of the film above method on the stele are spots of glue, to get rid of that can be read. On the part of the surface spray spray window cleaners, heat the stream of air from the dryer and the building very quickly, while hot glass, wipe it with newspaper space, exerting some effort. Repeat the process again and again until, while glass will not clean. Some craftsmen manage to cope with the process rastonirovki and without the use of a hair dryer. To do this after the film managed to hook area, its beginning to strip off parallel to the water spraying from the spray a few drops of baby shampoo in place of separation of glass and film. If everything is done slowly and carefully, most of the adhesive layer remains on the film rather than glass. The fact that the water in this case acts as an activator of the acrylic adhesive. After removal of the film will only have to cut glass with a slight adhesive residue, soak them with water and shampoo, and wiped dry surface. Various small helpers to your car you can buy in the automobile. Accessories for cars can be bought at online shop FoxCar.

To the color of the car found metallic effect, it must be painted with two coats. The first layer - the base, the second layer - paint. It is very important to select quality materials and of course to use them properly. Just need a more thorough preparation of the body. For the first layer of paint need to "Nitro", she will give the color and the desired effect, for the second layer of paint will be needed, it will give a shiny car, as well as protect the body from the external environment. So, the first stage of painting is the preparation of the body. In the first of its surface must be degreased. This will require antisilikonovaya liquid, it can be purchased in any auto shops, and clean towels. On one napkin to cause the liquid and the second will need to wipe the surface dry. This stage requires particular attention. Better quality than its produce, the better will be painting in general. The second stage - it's blowing a car. Blowing can be performed before and after de-oiling it. But to save time it can be done only after degreasing. Blowing should be carried out to remove all the small mote and dust, otherwise they shall cleave to the body during the painting and spoil the view. After rinsing the body additionally be treated dust cloth, with her removed to the smallest speck of dust. Next, the third stage - the application of paint. It should be done only with paint. So when painting is not a band or spots of different shades, it must be applied in two layers. The first layer, we can not hesitate to put on tap, with the help of this, we paint the spots of soil and give the body a uniform color. If you do not get the desired results, then painted again, but only after the evaporation of the solvent. The last deposited layer should be opaque, which means that evaporation occurred hardener. Only after that can be taken as the most important base layer, which should not retain the stripes and spots. To do this, add the solvent in the paint and increase the flow of air in the gun. Apply paint to spraying, you will need to make sure that the layer was deposited on the surface of the body evenly. And finally, the final stage - covering car polish. This stage is the easiest. Here the most important thing to prevent stains. Varnish should be applied uniformly in two or three layers. Between them to produce dried and tested for tack. To do this lightly presses his finger to the lacquered surface, and then detaches it, but will hear the sound of "plunk" and the particles of varnish should not stick to your finger. After just the second layer is uniformly covered with lacquer. Thoroughly dried. To speed up the drying can increase the temperature of the room where the painting is made. When necessary to apply a third layer. Painting a car is finished, but to bring everything to the mind, it must be polished. To do this, you will need an ordinary wax which is based, is wax or polish. Rub the polish to a soft cloth, in any case, it is impossible to do with the open sun, as sunlight heats the body, and polish on it starts to dry out very quickly.

Over time, Tinted car windows dim, loses its former brilliance, fade or it gets scratched. Thus, the car loses its appeal. In this situation, there is nothing for it but to replace the dubbing film. However, to toned glass machine, you need to get rid of the old toning. At the moment, car services, this service costs money, so here we tell you how you can rastonirovku own hands. This process requires a lot of attention and patience. And so, in order to implement rastonirovku yourself you will need: - Building dryer (dryers with a little power will not do) - a thin metal bench line or razor blades (old style) - for removing adhesive - high-quality detergent for windows. Process rastonirovki car windows. 1. Before you start rastonirovanie car windows, you should warm up the glass to room temperature. 2. The procedure for removal of dubbing the film. 3. Eliminating the adhesive layer from car windows. 4. Cleaning the glass by means of glasses. So, let's begin. To begin to remove the old tint from the glass you need to warm up to room temperature. This can be done by building a hair dryer. Take a hair dryer and uniformly heat the surface of the glass. Heating glass should be very careful not to get a strong overheating. Otherwise, the glass of your car can crack. Once you have warmed the glass, you can safely proceed to rastonirovaniyu. Find the edge of the film and gently pry the edge of the blade dubbing a film, and then slowly tear it off the glass. Once the film is removed, you need to get rid of the remaining glue on the glass. To do this, take the vehicle to clean the adhesive layer and spray it evenly across the surface of the glass. After spraying, the glass will foam, which should remain on the glass in the machine for 3-5 minutes. This tool contains ammonia, so if you can not buy it in specialty stores or you want to save money, you can to remove the adhesive layer to use an ordinary household ammonia. However, the use of ammonia is necessary accurately, he gets into the airways, so this procedure is best done in a respirator. Once you have finished cleaning glasses of glue, take a dry and clean rag and wipe the surface of glass. Then, look carefully to no adhesive residue left on the glass. If necessary, remove the remaining glue with the blade. In order to bring the process to the end rastonirovki car windows, wipe the glass with a clean cloth and a special glass cleaner. At this stage rastonirovanie finished, good luck! At rastonirovku glass of the car it will take approximately 3-4 hours. Disassembly of the doors and windows to carry out the dismantling is not needed.